Skip to product information
1 of 5

Arbitrend Puff

Arbitrend Puff

Arbitrend Puff is a special effect ink that creates a puff or emboss print effect. When subjected to heat, it expands, offering a distinctive tactile effect rather than a flat print. This base requires direct printing on the substrate and cannot be used as an overprint.

Highlight

  • Soft-hand feel with good washing fastness
  • Fashion-base effects with puff effect
  • Good printability and stability on screen
  • Easy cleanup with soap and water

Application

Direct to textile substrate only. Do not print on top of any water-based or plastisol print. For cut-piece articles and

Material Compatibility

  • 100% Cotton
  • 50/50 Cotton-polyester blend/synthetic fiber
  • Calico/Canvas

Screen Mesh

80T – 100T, monofilament

Instruction

Maintain medium pressure and speed with 45º to 60º angle when printing. To semi-cure, use heat gun and for final curing, it is recommended to use oven or flash cure machine. For heat press machine, use medium pressure to allow space for the ink to rise to a puff effect.
Must be printed directly onto the fabric.

Recommended Pigment Load

Maximum Pigment Load

ColorsPuff Base
Basic5%
Neon30%

Recommended Curing Parameters

  • Drying time : 10 seconds
  • Temperature : 110ºC (230ºF)
  • Equipment : Heat press/oven/flash cure
  • Pre-curing : Heat gun

Time and temperature may vary depending on the curing equipment used.

Clean Up

Wash materials used with soap and water. Observe all local regulations when disposing of this substance.

Storage and Handling

Store tightly covered at temperatures between 10ºC – 30ºC (50ºF – 86ºF) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures

Label Instruction

[EN]

Instruction

  • Stir well before using ink.
  • Pre-test fabric compatibility prior to mass production.
  • Wash test must be carried out 24 hours after printing.

Precaution

  • Wear protective gloves if there is continual contact of ink for sensitive skins.
  • Avoid any contact with eyes.
  • Wash hands thoroughly at the end of work.
  • Do not swallow.
  • Keep out of reach of children.

Storage and Handling

  • Ensure good ventilation at the workplace.
  • Close lid after use.
  • Dispose of the waste according to your local regulation.

[FR]

Instruction

  • Mélanger avant utilisation.
  • Tester sur échantillonnage avant
    production en masse.
  • Lavage 24 heures après impression.

Precaution

  • Porter des gants si il y a contact prolonge avec la peau si peaux sensibles.
  • Eviter tout contact avec les yeux.
  • Nettoyer vos mains après utilisation.
  • Ne pas avaler.

Entreposage et Manutention

  • A utiliser dans une pièce aérée.
  • Refermer couvercle après usage.
  • Veuillez disposer du produit suivant les normes en vigueur dans votre pays.
View Other Products
View full details
Important Note
This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.

While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.
Disclaimer
The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.

In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.

The information contained herein is liable to modification from time to time in light of continuous product development or improvements.