1 5

Arbitrans KL

Arbitrans KL

Arbitrans KL is a translucent water-based adhesive specially designed for use with transfer paper materials, facilitating the transfer of prints onto light and dark ground substrates. Its versatile formulation allows compatibility with three types of transfer papers—reflective, flock, and foil—for achieving striking printing effects. It has quick drying time and consistently reliable results.

Highlight

  • Used on 3 types of transfer paper (Reflective, flock, foil)
  • Good washing fastness
  • Soft-hand feel
  • Easy cleanup with soap and water

Application

Direct to textile printing. For cut-piece articles and ready-to-wear.

Material Compatibility

  • 100% Cotton
  • 50/50 Cotton-polyester blend/synthetic fiber
  • Calico/Canvas

Screen Mesh

80T – 120T, monofilament

Instruction

After curing, peel the transfer paper once it has cooled down, and then cure again without the transfer sheet (unless necessary). This also helps improve washing fastness of the print. For final curing, it is advisable that heat press machine is used instead of flat iron for even or balance curing.
All transfer prints have a tendency to wash-off after some washings. It is recommended that during laundry, the substrate is washed inside-out to make the print last longer.

Recommended Pigment Load

Not recommended

Recommended Curing Parameters

  • Drying time : 10 seconds
  • Temperature : 110ºC (230ºF)
  • Equipment : Heat press/oven/flash cure
  • Pre-curing : Heat gun

Time and temperature may vary depending on the curing equipment used.

Clean Up

Wash materials used with soap and water. Observe all local regulations when disposing of this substance.

Storage and Handling

Store tightly covered at temperatures between 10ºC – 30ºC (50ºF – 86ºF) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures.

Label Instruction

[EN]

Instruction

  • Stir well before using ink.
  • Pre-test fabric compatibility prior to mass production.
  • Wash test must be carried out 24 hours after printing.

Precaution

  • Wear protective gloves if there is continual contact of ink for sensitive skins.
  • Avoid any contact with eyes.
  • Wash hands thoroughly at the end of work.
  • Do not swallow.
  • Keep out of reach of children.

Storage and Handling

  • Ensure good ventilation at the workplace.
  • Close lid after use.
  • Dispose of the waste according to your local regulation.

[FR]

Instruction

  • Mélanger avant utilisation.
  • Tester sur échantillonnage avant
    production en masse.
  • Lavage 24 heures après impression.

Precaution

  • Porter des gants si il y a contact prolonge avec la peau si peaux sensibles.
  • Eviter tout contact avec les yeux.
  • Nettoyer vos mains après utilisation.
  • Ne pas avaler.

Entreposage et Manutention

  • A utiliser dans une pièce aérée.
  • Refermer couvercle après usage.
  • Veuillez disposer du produit suivant les normes en vigueur dans votre pays.
View Other Products
View full details
Important Note
This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.

While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.
Disclaimer
The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.

In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.

The information contained herein is liable to modification from time to time in light of continuous product development or improvements.