Arbiair Clear LCG is a transparent airbrush ink that is ideally suited for application on white and light-colored substrates, offering versatility in achieving the desired artistic effect.
Highlight
Soft-hand feel
Good washing fastness
Good printability and stability on screen
Easy cleanup with soap and water
Dual-purpose usage, airbrush and screen-print
Application
Arbiair series is compatible with airbrush tool and direct-to-textile printing on cut-piece articles and ready-to-wear outfit.
Material Compatibility
100% Cotton
50/50 Cotton-polyester blend
50/50 Cotton-synthetic fiber
Calico/Canvas
Screen Mesh
(For screen-printing) 80T-120T, monofilament
Instruction
For Airbrush Procedure
Prepare your airbrush/pen tool. Preferably use the double action type for greater control and easy clean, as a single action has less moving parts. Ideally, use at least a 100 P.S.I. air compressor and then prepare your inks and practice controlling atomization.
On use of color, clean the airbrush tool to prevent colors from mixing in the airbrush. Blow water out on a rag or a piece of scratch paper.
Wash out the airbrush tool immediately after you are done painting. Make sure to disassemble carefully for a sure clean.
For Screen-printing Procedure
The printing process can be done either manual or via automatic screen-printing. Suggested maximum of three [3] strokes, three [3] coats, except when printing tonal or CMYK process.
In halftone print, one [1] stroke is ideal but two [2] strokes are acceptable, however, one [1] coat only is highly suggested.
Curing is recommended to greatly increase washing fastness. Curing will also give the print a glossier print output.
Recommended Pigment Load
Maximum Pigment Load
Colors
Clear Base
Matte Base
Basic
5%
7%
Neon
15%
30%
Recommended Curing Parameters
Drying time : 10 seconds
Temperature : 110ºC (230ºF)
Equipment : Heat press/oven/flash cure
Pre-curing : Heat gun
Time and temperature may vary depending on the curing equipment used.
Clean Up
Wash materials used with soap and water. Observe all local regulations when disposing of this substance.
Storage and Handling
Store tightly covered at temperatures between 10ºC – 30ºC (50ºF – 86ºF) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures.
Label Instruction
[EN]
Instruction
Stir well before using ink.
Pre-test fabric compatibility prior to mass production.
Wash test must be carried out 24 hours after printing.
Precaution
Wear protective gloves if there is continual contact of ink for sensitive skins.
Avoid any contact with eyes.
Wash hands thoroughly at the end of work.
Do not swallow.
Keep out of reach of children.
Storage and Handling
Ensure good ventilation at the workplace.
Close lid after use.
Dispose of the waste according to your local regulation.
[FR]
Instruction
Mélanger avant utilisation.
Tester sur échantillonnage avant
production en masse.
Lavage 24 heures après impression.
Precaution
Porter des gants si il y a contact prolonge avec la peau si peaux sensibles.
Eviter tout contact avec les yeux.
Nettoyer vos mains après utilisation.
Ne pas avaler.
Entreposage et Manutention
A utiliser dans une pièce aérée.
Refermer couvercle après usage.
Veuillez disposer du produit suivant les normes en vigueur dans votre pays.
This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.
While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.
Disclaimer
The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.
In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.
The information contained herein is liable to modification from time to time in light of continuous product development or improvements.
Choosing a selection results in a full page refresh.